2011 CF Tube Amp Questions

The 5th Annual CarverFest Sep. 9th - 19th
Post Reply
User avatar
Dennis47
Newbie 50+
Posts: 95
Joined: Tue Jan 30, 2007 10:08 pm
Location: Indiana

2011 CF Tube Amp Questions

Post by Dennis47 » Mon Feb 25, 2019 8:17 pm

[img]

I'm thinking about purchasing this 2011 CF EL84 Tube Amp, but have the following questions
that, hopefully, someone can answer for me.

There is a 3 way toggle switch on the rear (between RCA's & speaker terminals),
I'm thinking it is a control for stereo/mono modes. Would that be correct? If not
what is it's function?

I can't tell from the tubes if this is wired for 6AX7 or 12AX7 tubes. The only ID
on the driver tubes is OTK7 9201. I think this is a vintage designation for Russian
Vokhod. Would that be true? Can the tube voltage be ascertained either by the
tube or by the pin wiring?

Thanks for the help.... #-o :-k
Attachments
IMG_2470.jpg
IMG_2466.jpg
IMG_2466.jpg (141.62 KiB) Viewed 347 times
IMG_2467.jpg
IMG_2465 (1).jpg
IMG_2465 (1).jpg (85.52 KiB) Viewed 347 times

hewlew1
"You Fuckin' Fucks"
Posts: 2152
Joined: Tue Feb 17, 2004 11:02 pm
Location: Northeast, Pa

Re: 2011 CF Tube Amp Questions

Post by hewlew1 » Mon Feb 25, 2019 8:44 pm

Dennis, I would agree as to the 3way switch. I can not tell by the pics as to 6ax7 or 12ax7 heater wiring. I will say that a lot of these amps were customized to the owners preference.. For example none of mine have a rear mounted power switch I chose to Install a B+ fuse holder in its place on mine. My power switch is mounted on the face and is illuminated also I installed an indicator light on the front of mine which lights when the amp is functioning as a monoblock. Just an FYI
20190221_165730.jpg
"Carver Audio, why settle for less, just ask my neighbors"
C1,C2,CT3,CT6,CT7/3,CT23,CT26,C4000,The Receiver,M500,M500T/6,M1.5T,TFM24/2,TFM/25/3,TFM35,TFM35X,TFM42/2,DTL200,TDR1700,DPL20,TX11/2, 5.2Center,5.1Sub/3,Original Amazings,Platinum Amazings/2,AL3'S,Polk SDA SRS, Polk SDA 1C's, Polk RTA11's, Polk Monitor 10's/2 ,Monitor 7's, Sunfire 300x2 /5, Sunfire pre, Sunfire MK2 Sub/2, 4 Carverfest monoblocks, Carverfest linestage preamp/2, Mapletree Audio Designs Tube Preamp,Phase Linear Andromeda III speakers, Phase Linear 4000 Preamp, Dahlquist DQ-10's
CERTIFIED AMPLE PLIERS EXPERT
Some of the best fuckings we get during our lifetime come from a relative!
I don't kiss ass, I dont take peoples shit, so dont expect it from me!

User avatar
Dennis47
Newbie 50+
Posts: 95
Joined: Tue Jan 30, 2007 10:08 pm
Location: Indiana

Re: 2011 CF Tube Amp Questions

Post by Dennis47 » Mon Feb 25, 2019 10:27 pm

hewlew1,

Thanks for the info.

Love what you've done with your amp...especially the wood side rails
and front power/indicator lamps. Very nice workmanship! =D>

User avatar
Ben D. Rinkin
M-400t CUBE
Posts: 106
Joined: Fri Dec 18, 2009 8:02 pm

Re: 2011 CF Tube Amp Questions

Post by Ben D. Rinkin » Tue Feb 26, 2019 2:10 am

TOOOOOOOOOOoooooooobbbbbbs!
Socialism takes and Capitalism creates

User avatar
Magnaryder
SILVER-7 TUBE AMP
Posts: 3219
Joined: Fri Mar 09, 2007 1:00 am
Location: Bucyrus, Ohio

Re: 2011 CF Tube Amp Questions

Post by Magnaryder » Tue Feb 26, 2019 10:37 am

Looking at the pics you provided I'd guess its a stereo/mono switch. Angelo's Work? Nicely done. There will be a jumper between 2 of the pins on the driver tubes, I couldn't make it out from the pics provided. This would raise the voltage to 12 volts instead of the 6 volts of the original design.

ray
Magnaryder

Its going to be used equipment when I sell it, so it may as well be used equipment when I buy it.

"Racing is life, the rest of the time you're just sitting around."-Steve McQueen

Post Reply

Return to “CARVERFEST 2011”