It is currently Mon May 04, 2015 9:02 am
Just found us? Entering CarverAudio.com for the first time? Post your introductions here and say hi to all of the other Carver enthusiasts.
Joined: Fri May 14, 2010 11:53 pm
Location: wisconsin,home of the Green Bay Packers!
Carver: TFM-45, PST-24 Cassette, Extra Carver Gear: CT-6, C-11 (S/N 00001).
Polk Audio: Mains SRS 2.1TL, Center CSiA6, Surrounds FXiA6 and FXiA4, Sub DSW MicroPro 1000, Extra Speakers SDA 2A, SDA 2Btl, Monitor 10A.
Turntable: Dual CS 714Q
Bluray/SACD: Oppo BDP 83SE
CD: Sony 330 300 Disk changer
PT-2400 serial #0001
Baby Black serial #0001
Baby Black serial #0002
Bone Stock Lightstar
Vintage Hi-Fi modified Lightstar
Sunfire Tube preamp
ProJect TT Tube preamp
DENON DP-62L TurnTable
More Douglas cables
OK ERIC, LET GO OF THE MOUSE AND BACK AWAY FROM YOUR PC WITH YOUR HANDS IN THE AIR. NOW SLOWLY LAY FACE DOWN ON THE FLOOR!!!! - Snoop65
Carver PM 600:
8-ohm FTC rated power/ch 200W
4-ohm FTC rated power/ch 300W
Bridged mono power 700W
4/8-ohm FTC rated THD 0.5%
IM Distortion less than 0.1%
Input Impedance (Line) 15k ohm
Input Sensitivity 1.5Vrms
Rated full power bandwidth +0, -3dB at 5Hz & 80kHz
Slew Rate 25V/u sec
Power Consumption 950 Watts
Fusing 8 amp slo-blo
Damping 200 at 1kHz
Dimensions (HxWxD inches) 3.5" x 19" x 11.56"
Architect's and Engineer's Specifications
The power amplifier being of two channels, shall deliver 200W into 8 ohms with both channels operating, or 300W into 4 ohms with both channels operating. The amplifier shall be capable of bridge-mode operation thereby providing 700W RMS output into 8 ohms and supplying a 70-volt distribution system without output matching transformers. The amplifier shall have a thermal shutdown system to protect the power devices from over-temperature operation. This thermal protection system shall be self-resetting. A protection LED indicator shall activate and the amplifier shall shut down to protect against short circuits and excessive high frequencies at the outputs, DC offset present at the outputs, or an internal power supply fault. The amplifier shall be capable of sequential turn-on/off and remote turn-on/off with a DC voltage between +5 and +15Vdc at the receive terminals. A delayed send voltage of 11Vdc shall be provided at the send terminals to turn subsequent amplifiers with this feature. The amplifier shall have slow start up and muted inputs of turn-on. Optional signal processing shall be available to be installed at the rear of the amplifier. The amplifier shall have a voltage gain of 28.5dB. Noise shall be at least 115dB below 40Vrms, A-Weighted, from 20Hz to 20kHz. Total harmonic distortion shall be less that 0.5% and inter modulation distortion shall be less than 0.1%. The front panel controls shall consist of independent level controls for left and right channels, a master power switch and a sequential operation switch. The dimensions shall allow for standard 19" EIA rack mounting. It shall be 3.5" high and 11.56" deep. The amplifier shall weigh 23 pounds. The power requirements shall be 120V, 60Hz, 960W. The frequency response shall be +0, -3dB at 3Hz and 80kHz. The power amplifier shall be CARVER PM-600.
• 300 + 300 watts into 4 ohms.
• High-efficiency linear tracking output design.
• Highly-regulated magnetic field power supply.
• L/R level controls with 11 precision detents.
• Remote/manual sequential power on/off.
• Dual-stage slow power-up.
• Clipping eliminator circuitry with back panel switch.
• Heavy duty 5-way speaker binding posts.
• XLR, TRS and barrier strip inputs.
• Switchable XLR pin configuration.
• Dual-channel 7-segment LED display.
- 1 bottom green "ON" LED per channel.
- 5 red output level LED's per channel.
- 1 yellow clipping/clipping eliminator indicator/protection activated LED per channel.
• Protection circuits:
- L/R-ch. Thermal.
- Independent L/R-ch. Short Circuit.
- Independent L/R-ch. Ultrasonic.
- DC offset.
• Rear cover card slot for use with Carver add-in options such as the PMX Crossover or PG2 Dual-Zone Paging Module.
• 70-volt transformer option.
• 70-volt direct drive capability.
• Passive convection cooling system.
Klipsch RB 81 II's
Klipsch RC 64 II
Samson SX3200 (750x2 Sub Amp)
Klipsch THX Ultra 2 Subs KW-120 (2)
C1,C2,CT3,CT6,CT7/3,CT23,CT26,C4000,The Receiver,M500,M500T/6,M1.5T,TFM24/2,TFM/25/3,TFM35,TFM35X,TFM42/2,DTL200,TDR1700,DPL20,TX11/2, 5.2Center,5.1Sub/3,Original Amazings,Platinum Amazings/2,AL3'S,Polk SDA SRS, Polk SDA 1C's, Polk RTA11's, Polk Monitor 10's/2 ,Monitor 7's, Sunfire 300x2 /5, Sunfire pre, Sunfire MK2 Sub/2, 4 Carverfest monoblocks, Carverfest linestage preamp/2, Mapletree Audio Designs Tube Preamp,Phase Linear Andromeda III speakers, Phase Linear 4000 Preamp, Dahlquist DQ-10's
CERTIFIED AMPLE PLIERS EXPERT
Some of the best fuckings we get during our lifetime come from a relative!
I don't kiss ass, I dont take peoples shit, so dont expect it from me!
Carver M4.0T in front channels to Caver AL VI's in SACD & 2 Channel setup
C 16, PT 2400, Slim Device, Carver TX-8, 490T and Rega TT w Grado Gold cart in the 2 channel setup
Bogen SRB20 is computer amp
Carver PM-350 donated for youth church use
Who is online
Users browsing this forum: Yahoo [Bot] and 0 guests